+1-203-359-4708 GOODWAY.COM 25 TUBE CLEANERS ACCESSORY APPLICATION PART NO. SIZES Adjustable Triangular Scraping Tools Removing heavy scale deposits in straight, ferrous tubes. They can only be used in a clockwise (forward) direction and cannot be used in internally enhanced tubes. They are adjustable to a 6,4 mm range. TST-500 TST-750 Triangular Scraper Tool for tubes 12,7 to 19,1 mm I.D.; Triangular Scraper Tool for tubes 19,1 to 25 mm I.D. Carbide Drills Carbide Drills are recommended for cleaning straight, ferrous tubes plugged solidly with deposit. PTB-025/037/ 043/050/ 056/062/068 6,4 mm, 9,5 mm, 11,1 mm, 12,7 mm, 14,3 mm, 15,9 mm or 17,5 mm (specify size) Flex-Hone Abrasive Tools Flex-Hone Abrasive Tools are light pressure, soft application honing devices for cleaning straight, ferrous tubes. They consist of 180 grit silicon carbide abrasive globules (stones) bonded to high density nylon filaments. Order tool to correspond to tube I.D. FHT-025/031/037/ 043/050/056/062/ 068/075/087/100 6,4 mm, 7,9 mm, 9,5 mm, 11,1 mm, 12,7 mm, 14,3 mm, 15,9 mm, 17,5 mm, 19,1 mm, 22,2 mm or 25 mm (specify size) NOTE: FLEX-HONE ABRASIVE TOOLS ARE NORMALLY USED WITH A WATER FLUSH FOR MAXIMUM LIFE. Flex Hub Tools Flex Hub Tools incorporate centrifugally activated blades for removing hard and heavy deposits in straight, ferrous tubes. GTC-225 GTC-225A Flex Hub for straight tubes 12,7 to 25 mm I.D.; Replacement Metal Blades for GTC-225 (set of three) U-Tube Tools Consisting of brushes or grinding tips permanently mounted on 460 mm sections of flexible shafts, U-Tube Tools are designed to snake partially through each side of a U-bend, to thoroughly clean from both sides. CBT-075B; CBT-075S WBT-075B/100B; WBT-075S/100S; GTT-050; GTT-625 Brass Cup Brush Tool for tubes 12,7 to 19,1 mm I.D. ; Stainless Steel Cup Brush Tool for tubes 12,7 to 19,1 mm I.D. ; Brass Wheel Brush, 19,1 mm or 25 mm (specify size) ; Stainless Steel Wheel Brush, 19,1 mm or 25 mm (specify size) ; Grinding Tip Tool, 12,7 mm; Grinding Tip Tool, 15,9 mm BRUSHES FOR SMOOTH BORE TUBES CONTINUED 6,4 TO 25 MM ONLY 6,4 TO 25 MM ONLY STAINLESS STEEL BRUSHES: Stainless Steel Brushes are recommended for removing soft and light scale deposits in straight, ferrous tubes. Brush should be equal to or 1,6 mm smaller than tube I.D. AVAILABLE IN BAGS OF 15 BRASS BRUSHES: Brass Brushes are recommended for removing soft and light scale deposits in straight, ferrous and nonferrous tubes. Brush should be equal to or 1,6 mm smaller than tube I.D. AVAILABLE IN BAGS OF 15 GTC-200BQ: Brass Brushes, 6,4 to 25 mm (in 1,6 mm increments). GTC-210Q: Stainless Steel Brushes, 6,4 to 25 mm (in 1,6 mm increments). BUFFING TOOLS GTC-205Q: Buffing Tool for tubes 12,7 to 14,3 mm I.D. GTC-205QDT: Same as GTC-205Q with drill tip. GTC-206Q: Buffing Tool for tubes 15,9 to 25 mm I.D. GTC-206QDT: Same as GTC-206Q with drill tip. GTC-207: Replacement Metal Blades for GTC-203 and GTC-204. GTC-208A: Replacement Metal Blades for GTC-205. GTC-208B: Replacement Metal Blades for GTC-206. Stainless Steel Wire Buffing Tools are used for removing light to medium scale deposits or for finishing tubes previously “roughed out” with other cleaning tools. They can be used in straight, ferrous and nonferrous tubes. Buffing tools can only be used in a clockwise (forward) direction and cannot be used in internally enhanced tubes. They are adjustable to a 6,4 mm range. GTC-203: Buffing Tool for tubes 7,9 to 9,5 mm I.D. GTC-203DT: Same as GTC-203 with drill tip. GTC-204Q: Buffing Tool for tubes 9,5 to 12,7 mm I.D. GTC-204QDT: Same as GTC-204Q with drill tip. 9,5 TO 25 MM ONLY Note: 6,4 mm and 7,9 mm threaded brushes require a #C-1 Coupling, and 9,5 mm threaded brushes require a #C-2 Coupling to connect to GTC-701 Flexible Shafts. (Couplings supplied with GTC-701 Flexible Shaft order.) Note: All Goodway brushes and buffing tools are available with standard threaded tool couplings. To order leave off the “Q” in the part number. BRUSHES AND TOOLS SAVE WITH QUICK CONNECT! FOR TUBES UP TO 25 MM - BRUSHES & SPECIALTY TOOLS
