+1-203-359-4708 GOODWAY.COM DUCT CLEANERS 41 OXINE® FRESHDUCT DUCT CLEANING EQUIPMENT — SHAFTS AND BRUSHES A. FLEXIBLE SHAFTS (NYLON CASING): For removing light to medium deposits in horizontal ducts up to 457 mm I.D. GTC-704-12-C: Flexible Shaft, 3,65 m. GTC-704-17-C: Flexible Shaft, 5,18 m. GTC-704-25-C: Flexible Shaft, 8 m. GTC-704-35-C: Flexible Shaft, 10,67 m. GTC-704-45-C: Flexible Shaft, 13,71 m. GTC-704-60-C: Flexible Shaft, 18,29 m. B. FLEXIBLE SHAFTS (HEAT RESISTANT): Heat resistant up to 149º C with rigid covered steel casing for removing light to medium deposits in horizontal ducts up to 457 mm I.D. GTC-704G-12-C: Flexible Shaft, 3,65 m. GTC-704G-17-C: Flexible Shaft, 5,18 m. GTC-704G-25-C: Flexible Shaft, 8 m. GTC-704G-35-C: Flexible Shaft, 10,67 m. GTC-704G-45-C: Flexible Shaft, 13,71 m. GTC-704G-60-C: Flexible Shaft, 18,29 m. C. FLEXIBLE SHAFTS (COVERED STEEL CASING) For removing heavy deposits in horizontal ducts up to 457 mm I.D. and in all vertical ducts GTC-721-15-C: Flexible Shaft, 4,57 m. GTC-721-25-C: Flexible Shaft, 8 m. GTC-721-35-C: Flexible Shaft, 10,67 m. GTC-721-50-C: Flexible Shaft, 15,24 m. NOTE: TO ORDER FLEXIBLE SHAFT(S) DETERMINE DUCT CONFIGURATION(S) AND LENGTH OF LONGEST SECTION(S) TO BE CLEANED. ORDER FLEXIBLE SHAFT(S) TO CORRESPOND WITH CONFIGURATION(S) AND LENGTHS. (CONSULT FACTORY FOR LONGER FLEXIBLE SHAFTS IF REQUIRED.) D. FAN BRUSH: The fan brush is recommended for removing debris in round, rectangular and square ducts. It both loosens and propels deposits down the duct towards the vacuum. FDB-212: Fan Brush, 203,2 mm - 464 mm. GTC-704-C GTC-704G-C GTC-721-C FAN BRUSH DUCT BRUSH FLARE BRUSH E. DUCT BRUSH: Soft nylon duct brushes are recommended for removing debris in round ducts. DUCT-04: Duct Brush, 102 mm. DUCT-06: Duct Brush, 150 mm. DUCT-08: Duct Brush, 203,2 mm. DUCT-10: Duct Brush, 254,0 mm. DUCT-12: Duct Brush, 305 mm. DUCT-14: Duct Brush, 355,6 mm. DUCT-16: Duct Brush, 406,4 mm. DUCT-18: Duct Brush, 464 mm. F. FLARE BRUSH: The flare brush is recommended for removing debris in round ducts. FBT-502: Flare Brush for ducts 102 mm - 203,2 mm I.D. G. OXINE®: This EPA-registered chemical kills any residual mold, bacteria, mildew, viruses, fungi, algae, and any other “living” matter. It is recommended for its low toxicity and safety and does not leave an active chemical residue (A 1 pint bottle will sanitize a 5-ton system four times). AQ-OX-Q: Oxine, 473 ml bottle. H. FRESHDUCT: Air ducts are often sources of odors caused by smoke, pets, cooking, spoilage and other agents. FreshDuct is specially formulated to control odors gently, but effectively. Its non-toxic, biodegradable formula encapsulates and destroys odor causing molecules on contact, while time releasing a fresh fragrance, freshening and deodorizing the interiors of both, lined and unlined ducts. FRESHDUCT-SPRAY: FreshDuct, 397 gram ready-to-use aerosol can. FRSHDCT-15OZ: FreshDuct, 425 gram concentrate bottle. FRSHDCT-05: FreshDuct, 19 liter concentrate bottle. A. B. C. D. E. F. G. H. BRUSHES AVAILABLE IN 101.6 MM, 203.2 MM, OR 254 MM
